Give a gift card. Let them choose their next make. Shop gift cards Skip to content
← Return to your step

Machine threading

Set up the Brother LX3817. Green shows the top thread; blue shows the bottom thread.

  1. 1Meet the machine

    Meet the machine

    Meet the machine. Find the parts used to thread and sew.

    Find the parts used to thread and sew.

  2. 2Connect the pedal

    Connect the pedal

    Connect the pedal. Push the foot-controller plug into the socket on the right side of the machine. Put the pedal on the floor.

    Push the foot-controller plug into the socket on the right side of the machine. Put the pedal on the floor.

  3. 3Plug into the wall outlet

    Plug into the wall outlet

    Plug into the wall outlet. Plug the power cord into the wall outlet.

    Plug the power cord into the wall outlet.

  4. 4Raise the presser foot

    Raise the presser foot

    Raise the presser foot. Lift the lever behind the needle to raise the presser foot.

    Lift the lever behind the needle to raise the presser foot.

  5. 5Raise the needle

    Raise the needle

    Raise the needle. Turn the handwheel toward you until its mark points up.

    Turn the handwheel toward you until its mark points up.

  6. 6Place bobbin on spool pin

    Place bobbin on spool pin

    Place bobbin on spool pin. Raise the spool pin and place a wound plastic bobbin on it. Let the thread unwind toward the top guide.

    Raise the spool pin and place a wound plastic bobbin on it. Let the thread unwind toward the top guide.

  7. 7Use the top guide

    Use the top guide

    Use the top guide. Draw thread from the upper bobbin through the rear guide, then toward the front groove.

    Draw thread from the upper bobbin through the rear guide, then toward the front groove.

  8. 8Down and around

    Down and around

    Down and around. Follow the right channel down, around the bottom, and up the left channel.

    Follow the right channel down, around the bottom, and up the left channel.

  9. 9Catch the take-up lever

    Catch the take-up lever

    Catch the take-up lever. Pass through the raised lever from right to left.

    Pass through the raised lever from right to left.

  10. 10Behind the needle guide

    Behind the needle guide

    Behind the needle guide. Bring the thread down behind the small guide above the needle.

    Bring the thread down behind the small guide above the needle.

  11. 11Thread front to back

    Thread front to back

    Thread front to back. Pass through the needle eye from front to back. Leave about 2 inches behind the foot.

    Pass through the needle eye from front to back. Leave about 2 inches behind the foot.

  12. 12Open the bobbin cover

    Open the bobbin cover

    Open the bobbin cover. Keep the needle and foot raised. Slide the cover toward you and lift it off.

    Keep the needle and foot raised. Slide the cover toward you and lift it off.

  13. 13Drop in the bobbin

    Drop in the bobbin

    Drop in the bobbin. Use a wound SA156 bobbin. Its thread must unwind counterclockwise.

    Use a wound SA156 bobbin. Its thread must unwind counterclockwise.

  14. 14Follow the slit and cut

    Follow the slit and cut

    Follow the slit and cut. Hold the bobbin gently. Follow the slit under the spring, then pull toward the cutter.

    Hold the bobbin gently. Follow the slit under the spring, then pull toward the cutter.

  15. 15Close the cover

    Close the cover

    Close the cover. Seat the cover tab and close it. The quick-set bobbin is ready; no pull-up is required.

    Seat the cover tab and close it. The quick-set bobbin is ready; no pull-up is required.

  16. 16Switch on

    Switch on

    Switch on. When threading is complete, press I on the power switch. The pedal controls sewing speed.

    When threading is complete, press I on the power switch. The pedal controls sewing speed.

Tips
  1. 1Optional: leave a bobbin tail

    Optional: leave a bobbin tail

    Optional: leave a bobbin tail. To draw up the lower thread, reinstall the bobbin without cutting its tail. Leave the cover off.

    To draw up the lower thread, reinstall the bobbin without cutting its tail. Leave the cover off.

  2. 2Catch the lower thread

    Catch the lower thread

    Catch the lower thread. Hold the upper thread. Turn the wheel toward you one full turn; pull up the bobbin loop.

    Hold the upper thread. Turn the wheel toward you one full turn; pull up the bobbin loop.

  3. 3Tails toward the back

    Tails toward the back

    Tails toward the back. Put about 4 inches of both threads behind the raised foot. Replace the cover.

    Put about 4 inches of both threads behind the raised foot. Replace the cover.

Credits [2][4]